Loading...

TILE & GROUT SEALANTS

MAIN FEATURES

  • AVOID WATER LEAKAGE THROUGH GROUTS
  • APPLY AFTER THE CONTRUCTION
  • READY TO USE
  • SLOWER DRYING FORMULA

BENEFITS

  • Helps permanently avoid oil and water-based stains
  • Preserves and protects against discoloration- no pooling or flaking off the surface
  • Blocks moisture penetration that causes mould and mildew
  • Can be used both on porous and non-porous surfaces
  • Ideal for both interior and exterior usage
  • Resists UV degradation
  • Slower drying formula
  • No coefficient of friction alteration

DIRECTIONS FOR USE:

Preparing the Surface : Always test product on an inconspicuous area for suitability. Surfaces should be clean and free from any waxes, coatings, or finishes. Read the label directions before application. This product can be applied to help protecting grout, unglazed ceramic tile, porcelain tiles, sandstone, Bluestone, Bricks, concrete, cement, quarry tile, terracotta, slate, marble, granite, agglomerates and many other masonry products from oil and water-based stains. Not harmful for aluminum, wood or carpet.

Application Instructions : Use the Mr. Seal sealant as it is, without diluting any other liquid. Be careful to prevent any painted or stained surface adjacent to application area. Apply on a surface as a thin, even coat using a pump, airless sprayer, brush, rag, mop or roller. Before the applied coat is completely dry, buff with a clean cloth. A treated surface will be completely dry within an approximate duration of 2 - 3 hours, but for maximum long lasting results, the treated area should be kept dry and free from soils for at least 24 hours. One coat is normally sufficient, but a second application is recommended on more porous surfaces or heavy walkway areas to ensure complete coverage and long lasting effects. Apply the second coat after a period of ½ hour – 1 hour from the first application. With some highly polished surfaces, such as granite or marble, an initial coat, followed by a light coat, is recommended. If a second coat is required, follow initial application instructions.

Maintenance : If a spillage occurs, absorb immediately with a clean cloth or a white paper towel. A sponge along with cold clean water should be used to clean any residue or a dried liquid. Do not scrub. For a semi- solid or a greasy stain, remove the spilled material as much as possible with a spoon or a blunt knife. Mix warm water with a small amount of mild detergent and sponge the stain gently until it is removed. Any left out residue of detergent should be removed immediately with clean and clear water.

Cleaning Application Equipment: Rinse equipment with turps, followed by a rinse with warm water.

Coverage : 1 Liter will be approximately sufficient to cover up an area of 40 sq. metres.

Safety Directions : Highly flammable. Liquid and vapour is harmful or fatal if swallowed. Use in a well-ventilated area. Open any doors and windows available and ventilate the area properly. Use fans if necessary. Extinguish heat sources and keep away from heat, open flames, sparks, oxidizing materials, and from possible ignition sources distant from application site (i.e. pilot lights, cigarettes, etc.) Do not smoke in the area surrounding the application is happening. Do not breathe gas/fumes/vapour/spray. Avoid contact with skin and eyes. Wash hands thoroughly with soap and water after usage.

Storage and Disposal : Protect the container from sunlight and do not expose to temperatures exceeding 50 o C. Do not pierce or burn even when the container is empty. Dispose with garbage or leave at an appropriate metal recycling collection point.

Why MR Seal

  • DIY product
  • Penetrating Sealer
  • Applied on old & new properties
  • No colour change on the surface
  • Allows the surface to breath
  • Stops Water absorption
  • Resists UV degradation
  • Suitable for interior & exterior use
  • Easy to apply & Maintain
  • Mold & mildew resistant
  • No silicones
  • Special formula for Swimming pool

Our Products

Media

Inquiry

Please send your inquiries to us
 
 

Your message was sent successfully!
One of our staff members will be in touch with you as soon as possible regarding your inquiry.
Thank you for reaching out to us.

Something went wrong, try refreshing and submitting the form again.

Contact Us

Our Address - Office :

208, Sea Street, Colombo 11, Sri Lanka

Phone Number : 0776 779 274
Email Address : info@mrseal.lk
Our Address - Factory :

83, Maithree Mawatha, Ekala, Ja-ela, Sri Lanka

Phone Number : 0776 779 274
Email Address : info@mrseal.lk